French Drain Calculator
Calculate drainage gravel, perforated pipe, filter fabric, trench spoil and minimum slope for a yard, downspout or foundation French drain, with an optional material cost estimate.
French Drain Calculator: How Much Gravel, Pipe & Fabric Do I Need?
A French drain is a gravel-filled trench with a perforated pipe in the bottom that collects groundwater and surface water and carries it downhill to a safe outlet. It is the go-to fix for soggy lawns, water pooling against a foundation, wet basements caused by high groundwater, and runoff coming down a slope from a neighbor's yard. Done right it is invisible and lasts decades; done wrong — no fabric, no slope, no real outlet — it silts up and stops working within a few years.
The material list is simple: washed drainage stone (usually #57, about 3/4"–1"), a 4" perforated pipe, and non-woven filter fabric that lines the trench and wraps over the top of the stone to keep soil out. Gravel volume is the trench length × width × gravel depth minus the space taken by the pipe. A typical 12" wide × 18" deep yard drain needs about 0.052 cubic yards of stone per foot — roughly 1 ton for every 12 feet including 10% extra.
Slope is not optional. The trench bottom must fall at least 1/8" per foot (about 1%) toward the outlet, and 1/4" per foot is better on long runs. That means a 50 ft drain drops at least 6¼" from end to end, so the trench gets deeper as it goes unless the ground already slopes. The outlet can be a daylight exit on a lower part of the property, a pop-up emitter, a dry well, or a storm sewer connection where your municipality allows it — never onto a neighbor's property.
In 2026 US pricing, washed #57 stone runs about $35–$65 per ton plus delivery, 4" perforated corrugated pipe with a sock about $0.80–$1.50 per foot (rigid PVC perforated pipe $2–$4 per foot), and non-woven geotextile fabric about $0.15–$0.35 per sq ft. DIY materials typically come to $5–$15 per linear foot. Professionally installed yard French drains usually cost $25–$60 per foot, and interior or foundation-footing drains $50–$100+ per foot because of excavation and waterproofing.
The French drain is one of several drainage tools. If water is mostly coming off the roof, extending downspouts or adding a buried downspout line is cheaper. If the whole yard slopes toward the house, regrading may be the real fix. For water behind a retaining wall, the drain is built into the backfill as the wall goes up — use our retaining wall drainage calculator for that layout. Our French drain cost guide and yard drainage solutions guide compare the options in detail.
French Drain Supplies
Recommended tools & materials — as an Amazon Associate, we earn from qualifying purchases.
Perforated Drain Pipe with Sock
Corrugated pipe pre-wrapped in filter fabric to keep silt out
Filter Fabric (Geotextile)
Wraps the gravel trench so soil can't clog the drain
Trenching Shovel
Narrow blade digs clean drain trenches with less spoil
How to Use This Calculator
Understanding Your Result
Gravel includes 10% extra, fabric 10% for overlaps and pipe 5% for fittings and the run to the outlet, so these are buy quantities. The fabric width shown is the minimum roll width that lines the trench in one piece. The fall figure is the minimum drop the trench bottom needs between its start and the outlet.
Key Formulas
Gravel Volume
All dimensions in feet. Multiply by 1.4 for tons of #57 stone.
Filter Fabric
Lines both walls and the floor, with the top overlap folded over the stone.
Minimum Fall
1/8" per foot minimum slope from the high end to the outlet.
Worked Example
A 50 ft yard French drain, 12" wide × 18" deep, with a 4" perforated pipe and gravel to the surface.
- 1Trench volume = 50 × 1 × 1.5 = 75 cu ft
- 2Pipe volume = π × (4 ÷ 24)² × 50 = 4.36 cu ft
- 3Gravel = 75 − 4.36 = 70.64 cu ft = 2.62 cu yd; + 10% = 2.88 cu yd ≈ 4.03 tons
- 4Fabric = 50 × (2 × 1.5 + 2 × 1) × 1.10 = 275 sq ft on a roll at least 5 ft wide
- 5Pipe = 50 × 1.05 = 53 ft → one 100 ft coil
- 6Fall = 50 × 0.125 = 6.25"; spoil = 75 × 1.25 ÷ 27 = 3.47 cu yd
Order about 4 tons of washed #57 stone, a 100 ft coil of 4" perforated pipe and 275 sq ft of non-woven fabric. At $50 per ton, $1.20 per foot of pipe and $0.20 per sq ft of fabric, materials are roughly $320 — about $6.40 per foot.
Assumptions Behind This Estimate
- Washed #57 drainage stone at 1.4 tons per cu yd, +10% extra
- Pipe volume subtracted using nominal pipe diameter
- Fabric lines both trench walls and floor with the top overlap folded over the stone, +10%
- Pipe length = drain length + 5%; outlet piping beyond the drain not included
- Excavated soil swells about 25% once dug
- Minimum slope of 1/8" per foot
French Drain Materials per 10 Feet
| Trench Size | Gravel (cu yd) | Gravel (tons) | Fabric (sq ft) |
|---|---|---|---|
| 6" × 12" | 0.17 | 0.24 | 33 |
| 12" × 18" | 0.58 | 0.81 | 55 |
| 12" × 24" | 0.78 | 1.09 | 66 |
| 18" × 24" | 1.19 | 1.66 | 77 |
Width × depth. Stone at 1.4 tons per cu yd. Add pipe at the drain length plus 5%.
Before You Buy: Practical Advice
- Call 811 a few days before digging — shallow gas, irrigation and cable lines often cross drain routes.
- Rent a trencher for runs over about 30 ft; hand-digging 18" deep is slow, hard work.
- Check the trench floor slope every few feet with a string line before adding any gravel.
- Add a cleanout or a capped riser at the high end so the pipe can be flushed with a hose later.
- Make sure the outlet discharges onto your own property, away from the foundation and not onto a neighbor.
Frequently Asked Questions
How much gravel do I need for a French drain?
Multiply length × width × gravel depth in feet, subtract the pipe volume and divide by 27 for cubic yards. A 50 ft drain 12" wide and 18" deep with a 4" pipe needs about 2.6 cubic yards of stone, or about 2.9 cubic yards and 4 tons with 10% extra. Roughly, a 12" × 18" trench takes about 1 ton of stone per 12 feet.
How deep and wide should a French drain be?
Most yard drains are 6"–12" wide and 18"–24" deep. Drains intercepting groundwater near a foundation are usually deeper, often down to footing level. Make the trench at least 6" wider than the pipe so stone surrounds it, and remember the trench deepens along its length to keep the minimum 1/8" per foot fall.
Should French drain pipe holes face up or down?
Down, in most cases. Water rises into the pipe from the bottom of the trench as the water table in the gravel rises, and holes facing down let silt settle out rather than fall straight into the pipe. Set the pipe on about 2" of gravel so the holes sit slightly above the trench floor.
Do I need filter fabric for a French drain?
Yes. Non-woven geotextile fabric lining the trench and folded over the top of the stone stops fine soil from migrating into the gravel and pipe, which is the main reason French drains clog. A socked pipe alone is not enough in silty or clay soils. Avoid woven fabric, which lets water through much more slowly.
How much slope does a French drain need?
At least 1/8" per foot, or about 1%, and 1/4" per foot (2%) is better where possible. Over 100 ft that is a drop of 12.5"–25". Check the trench bottom with a string line and line level or a laser level as you dig rather than relying on the surface, which may not slope evenly.
Can I cover a French drain with grass?
Yes. Stop the gravel about 3"–4" below the surface, wrap the fabric over the stone, then add topsoil and sod. Use the soil cap field in the calculator to reduce the gravel accordingly. Leaving the gravel exposed at the surface captures surface runoff better, so many homeowners leave it open in low spots and capped elsewhere.
Related Calculators
Helpful Guides
Dive deeper with these related guides to plan your project with confidence.