Roof Pitch & Rafter Calculator
Convert roof pitch to an angle, find the total rise, common rafter length with overhang, plumb and seat cut angles, rafter count and roof area in squares for a gable roof.
Roof Pitch Calculator: Pitch to Angle, Rafter Length & Roof Area
Roof pitch is the number of inches a roof rises for every 12 inches of horizontal run, written as x:12 or x/12. A 6:12 roof climbs 6" per foot, which equals a 26.57° angle and a 50% slope. Pitch drives almost everything on a roofing job: which materials are allowed, how much surface area there is to cover, how long the rafters must be, and whether the crew can walk on it or needs roof jacks and harnesses.
To measure an existing roof, hold a level horizontally against the roof surface (or a rafter in the attic), mark 12" along the level, and measure straight up from that mark to the roof — that number is the pitch. You can also measure any rise and run and the calculator scales it to x:12. From pitch the key number is the pitch multiplier, √(1 + (pitch ÷ 12)²): multiply any horizontal distance by it to get the true sloped length. A 6:12 multiplier is 1.118, so a roof with a 1,200 sq ft footprint has about 1,342 sq ft of surface.
For a simple gable roof the common rafter length runs from the ridge to the outside of the wall plate. Take half the building span, subtract half the ridge board thickness (¾" for a 1½" ridge), and multiply by the pitch multiplier. Add the overhang (also multiplied) for the full rafter length, then round up to the next stock lumber length. The plumb cut at the ridge equals the roof angle, and the seat cut of the bird's mouth is the complement (90° minus the angle).
Pitch also sets material rules. Asphalt shingles need at least 2:12 and, below 4:12, a double layer of underlayment; standing seam metal can go to about 1:12 to 3:12 depending on the panel; anything flatter needs a membrane such as TPO or EPDM. In 2026 US pricing, roofing labor typically rises 10%–25% on roofs steeper than 8:12 and 25%–50% above 10:12 because of safety equipment and slower work, on top of the extra area the multiplier adds.
This calculator gives geometry — angles, lengths, counts and areas — not structural sizing. Rafter size and spacing must come from your local span tables (IRC R802 in most of the US), which depend on snow load, dead load, lumber species and grade. Use our roofing calculator to turn the roof area into shingle bundles, and the joist span calculator for floor and ceiling framing.
Roof Measuring Tools
Recommended tools & materials — as an Amazon Associate, we earn from qualifying purchases.
Laser Distance Measure
Measures rise, run and building width from the ground in seconds
Digital Angle Finder
Reads roof angle directly on a rafter or the shingle surface
Rafter Square
Lays out pitch, plumb cuts and birdsmouths on rafters
How to Use This Calculator
Understanding Your Result
Pitch, angle and the multiplier describe the slope itself. If you enter a span you also get the total rise from the top plate to the ridge, the common rafter length from ridge to plate, the full rafter length including the overhang and the stock length to buy. With a building length you also get the rafter count for both sides and the roof surface area in squares.
Key Formulas
Roof Angle
Gives the plumb-cut angle; the seat cut is 90° − angle.
Pitch Multiplier
Converts horizontal distance or area to sloped length or area.
Common Rafter Length
Span and overhang in feet; ridge board deduction is ¾" for a 1½" ridge.
Worked Example
A 28 ft wide × 40 ft long gable roof at 6:12 with a 1½" ridge board, 12" overhangs and rafters 16" on center.
- 1Angle = atan(6 ÷ 12) = 26.57°; multiplier = √(1 + 0.5²) = 1.1180
- 2Total rise = 14 × 0.5 = 7 ft
- 3Run = 14 − 0.75 ÷ 12 = 13.9375 ft; rafter body = 13.9375 × 1.118 = 15.58 ft (15' 7")
- 4With overhang = 15.58 + 1 × 1.118 = 16.70 ft (16' 8⅜") → buy 18 ft boards
- 5Rafters = ⌈480 ÷ 16⌉ + 1 = 31 per side → 62 total
- 6Roof area = 40 × (28 + 2) × 1.118 = 1,342 sq ft = 13.4 squares
The roof rises 7 ft at a 26.57° angle. Each rafter is 16' 8⅜" including the overhang, cut from 18 ft stock, and the roof needs 62 common rafters and about 13.4 squares of roofing before waste.
Assumptions Behind This Estimate
- Simple symmetrical gable roof with a ridge board
- Ridge board 1½" thick (¾" deducted from each run)
- Overhang measured horizontally from the wall to the fascia
- Rafter count = length ÷ spacing + 1 per side; no extras for gable-end ladders or openings
- Roof area includes eave overhangs but not gable rake overhangs or waste
- Geometry only — rafter size and grade must come from local span tables
Common Roof Pitches
| Pitch | Angle | Multiplier | Area Added vs Footprint |
|---|---|---|---|
| 3:12 | 14.04° | 1.0308 | +3% |
| 4:12 | 18.43° | 1.0541 | +5% |
| 6:12 | 26.57° | 1.1180 | +12% |
| 8:12 | 33.69° | 1.2019 | +20% |
| 10:12 | 39.81° | 1.3017 | +30% |
| 12:12 | 45.00° | 1.4142 | +41% |
Multiply the roof footprint (including overhangs) by the multiplier to get the actual roof surface area.
Before You Buy: Practical Advice
- Cut one pattern rafter, test-fit it at both ends of the building, then use it to mark the rest.
- Crown every rafter (hump side up) before cutting so the roof plane stays straight over time.
- Don't cut the bird's mouth seat deeper than one-third of the rafter depth.
- Above 8:12, budget for roof jacks, toe boards and fall protection — and higher roofing labor.
- Check local snow load requirements before choosing rafter size and spacing; trusses may be cheaper for long spans.
Frequently Asked Questions
How do I convert roof pitch to degrees?
Divide the rise by 12 and take the arctangent: angle = atan(pitch ÷ 12). Common values: 3:12 = 14.04°, 4:12 = 18.43°, 5:12 = 22.62°, 6:12 = 26.57°, 8:12 = 33.69°, 10:12 = 39.81° and 12:12 = 45°. The percentage slope is simply pitch ÷ 12 × 100, so 6:12 is a 50% slope.
How do I calculate rafter length?
Find the run (half the building span minus half the ridge board thickness) and multiply by the pitch multiplier √(1 + (pitch ÷ 12)²). Add the overhang multiplied by the same factor. For a 28 ft span at 6:12 with a 12" overhang, that is 13.94 × 1.118 + 1.118 = 16.70 ft, so you buy 18 ft boards.
What is the most common roof pitch?
Most US homes have roofs between 4:12 and 9:12, with 6:12 being the most common for new construction. These pitches shed water and snow well, accept standard asphalt shingles and are still walkable for roofers. Low-slope 2:12–3:12 roofs are common on porches and additions; 10:12 and steeper suit Tudor, Victorian and A-frame styles.
How does roof pitch affect roofing cost?
Steeper roofs cost more in two ways: more surface area (a 12:12 roof has 41% more area than its footprint, a 6:12 only 12%), and higher labor because crews need jacks, harnesses and slower work. Expect labor premiums of about 10%–25% above 8:12 and up to 50% on very steep roofs in 2026.
What is the minimum pitch for shingles?
Asphalt shingles can be installed down to 2:12, but roofs between 2:12 and 4:12 require two layers of underlayment (or self-adhered ice and water membrane) per IRC R905.2. Below 2:12, use a low-slope system such as TPO, EPDM, modified bitumen or certain standing seam metal panels rated for low pitches.
How do I measure roof pitch from the ground?
From the ground, use a smartphone pitch app or a pitch gauge held against the gable rake from a distance, or measure in the attic: place a level against the underside of a rafter, mark 12" along the level and measure vertically to the rafter. You can also measure the gable's total rise and half-span and enter them as rise and run.
Helpful Guides
Dive deeper with these related guides to plan your project with confidence.